Should I Change the Fluid in my Fluid Head?

Standard

Fluid video heads that use a fluid filled cartridge are not like cars.  The fluids do not need to be replaced unless they are broken.

fluid disk

Disassembled fluid disks

First, the fluid disc is a series of concentric circles that trap the fluid in them and slow the movement down by providing resistance.  The discs are generally inert and the fluid stays in place.  You don’t need to replace the fluid in the cartridge unless one of several things occur.

If the head has been stored in an excessively hot place for a long time, then there is a good change that the “fluid” has thinned because of the heat and settled, leaving half of the disc

fluiddisk2

Damaged fluid disk assembly

empty.  The discs are no longer parallel, the fluid, if it is still in the disc, and the fluid is all at one side.  This will greatly impair the smoothness and the feel of the head.  The heat can often make the fluid thin enough to escape the disc and run out.  If you’ve ever experienced the thick, sticky, gooey, almost impossible to clean off fluid then you will know what I am talking about.  In this case the fluid can be cleaned off and the discs refilled.

If the head was dropped and the fluid discs have been damaged then they should be replaced.  The little prongs sticking out of both sides can be sheared off if the head falls over or is impacted with enough force.

The discs are specific to different video heads, so it is best to start here for current heads, or here for other heads and getting the parts specific to it.

If you are having problems determining what parts you need, or for a tune up or for repairs, send your name, address, daytime phone and email address along with your tripod to:

ManfrottoTripodParts.com Repairs
c/o SpartanPhotoCenter
108 Garner Road
Spartanburg, SC 29303

Once we have it, we will evaluate it and contact you. Please send us your daytime phone so we can reach you during business hours.

Lastly, if we are repairing your Manfrotto Product; we are recycling all broken parts and scrap articles. Almost nothing goes into the trash if we can help it.

 

 

 

Advertisements

What is the Hole on the Side of My Tripod?

Standard

I have an MT190XPRO3 tripod and there is a hole in the side of it.  What is this?

This is the accessory screw port.  This has been a feature on Manfrotto tripods all the way back to when they were called Bogen.  It is basically a 3/8 screw hole that allows you to add a strap, 244MicroKitadd accessory arms or attach loops and other things to the tripod easily.  This is available on all the current MT190XPRO and MT055XPRO tripods.  There is a rubber cover to protect the threads and center column workings from debris.

The current accessory screw port has notch int he top and bottom that allows for the use of an non-rotating arm.  The previous 190 and 055 tripods can accept the arms, though they may rotate and flop about if the arm is twisted or set at the wrong angle.  We do not recommend the AR versions for the older tripods.  You can find more info about the arms on the page listed below.

More information about:
Manfrotto 244 Mini Arms
Clip on strap that does not use accessory screw port

If you are having problems determining what parts you need, or for a tune up or for repairs, send your name, address, daytime phone and email address along with your tripod to:

ManfrottoTripodParts.com Repairs
c/o SpartanPhotoCenter
108 Garner Road
Spartanburg, SC 29303

Once we have it, we will evaluate it and contact you. Please send us your daytime phone so we can reach you during business hours.

Lastly, if we are repairing your Manfrotto Product; we are recycling all broken parts and scrap articles. Almost nothing goes into the trash if we can help it.

 

 

We now have parts for the New BeFree Live Video Tripod & Head

Standard

We are now stocking almost all parts for the BeFree Live tripod and most losable parts on the MVK400 Video head.  You can find the complete listing Here.

There is little that is different in the basic tear down and repair of this tripod or head.  Basic tools are needed, Torx T20, flat blade screw driver or Allen wrench; depending upon what you are working on.

The most likely parts you will loose or damage are the Leg Snap Levers, there are 3 sizes; the Center Column Locking Knob or the Bag Hook on the bottom of the center column.

The head we have already seen that the pan handle and the Pan Handle Locking Knob are going to be trouble.  The pan handle is prone to breakage, ESPECIALY of the tripod tips over and hits on the Pan Tightening Knob.

Make sure you are following the basic rules of tripod use and you should not have a problem.

If you are having problems determining what parts you need, or for a tune up or for repairs, send your name, address, daytime phone and email address along with your tripod to:

ManfrottoTripodParts.com Repairs
c/o SpartanPhotoCenter
108 Garner Road
Spartanburg, SC 29303

Once we have it, we will evaluate it and contact you. Please send us your daytime phone so we can reach you during business hours.

Lastly, if we are repairing your Manfrotto Product; we are recycling all broken parts and scrap articles. Almost nothing goes into the trash if we can help it.